-- -- "%Z%%M% %D%" -- -- Title: Fibre Alliance Fibre Channel Management Framework Integration MIB -- Rev 1.5, June 1, 1999. -- -- Note: This is released for Brocade FOS 2.2 -- -- added FA MIB Version 2.2 last edited on Nov 10th, 1999. FCMGMT-MIB -- Last edit date: Nov 10th, 1999 DEFINITIONS ::= BEGIN IMPORTS IpAddress, TimeTicks, experimental FROM RFC1155-SMI OBJECT-TYPE FROM RFC-1212 DisplayString FROM RFC1213-MIB TRAP-TYPE FROM RFC-1215; --Textual conventions for this MIB FcNameId ::= OCTET STRING (SIZE(8)) FcGlobalId ::= OCTET STRING (SIZE(16)) FcEventSeverity ::= INTEGER { unknown (1), emergency (2), alert (3), critical (4), error (5), warning (6), notify (7), info (8), debug (9), mark (10) -- All messages logged } FcUnitType ::= INTEGER { unknown(1), other(2), -- none of the following hub(3), -- passive connectivity unit -- supporting loop protocol. switch(4), -- active connectivity unit -- supporting multiple protocols. gateway(5), -- unit that converts not only -- the interface but also encapsulates -- the frame into another protocol. The -- assumption is that there is always -- two gateways connected together. For -- example, FC <-> ATM. converter(6), -- unit that converts from one -- interface to another. For -- example, FC <-> SCSI. hba(7), -- host bus adapter proxy-agent(8), -- software proxy-agent storage-device(9), -- disk,cd,tape,etc host(10), -- host computer storage-subsystem(11), -- raid, library, etc module(12), -- subcomponent of a system swdriver(13), -- software driver storage-access-device(14) -- Provides storage management -- and access for hetergeneous -- hosts and heterogeneous devices. } ---------------------------------------------------------------------- fcmgmt OBJECT IDENTIFIER ::= { experimental 94 } -- groups in fcmgmt connSet OBJECT IDENTIFIER ::= { fcmgmt 1 } trapReg OBJECT IDENTIFIER ::= { fcmgmt 2 } statSet OBJECT IDENTIFIER ::= { fcmgmt 4 } revisionNumber OBJECT-TYPE SYNTAX DisplayString (SIZE (4)) ACCESS read-only STATUS mandatory DESCRIPTION "This is the revision number for this MIB. The format of the revision value is as follows (0) = high order major revision number (1) = low order major revision number (2) = high order minor revision number (3) = low order minor revision number The value will be stored as an ASCII value. The following is the current value of this object. (0) = '0' (1) = '2' (2) = '2' (3) = '0' This defines a revision of 02.20 " ::= { fcmgmt 3 } -- the connectivity unit group -- Implementation of the group is mandatory for all systems. uNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of connectivity units present on this system (represented by this agent). May be a count of the boards in a chassis or the number of full boxes in a rack." DEFVAL { 1 } ::= { connSet 1 } systemURL OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The top-level URL of the system. If it does not exist the value is empty string. The URL format is implementation dependant and can have keywords embedded that are preceeded by a percent sign (eg, %USER). The following are the defined keywords that will be recognized and replaced with data during a launch. USER - replace with username PASSWORD - replace with password GLOBALID - replace with globalid SERIALNO - replace with serial number " DEFVAL { "" } ::= { connSet 2 } statusChangeTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS deprecated DESCRIPTION "The sysuptime timestamp in centiseconds at which the last status change occurred for any members of the set." ::= { connSet 3 } configurationChangeTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS deprecated DESCRIPTION "The sysuptime timestamp in centiseconds at which the last configuration change occurred for any members of the set. This represents a union of change information for connUnitConfigurationChangeTime." ::= { connSet 4 } connUnitTableChangeTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS deprecated DESCRIPTION "The sysuptime timestamp in centiseconds at which the connUnitTable was updated (an entry was either added or deleted." ::= { connSet 5 } -- The Connectivity table contains general information on the -- system's units. connUnitTable OBJECT-TYPE SYNTAX SEQUENCE OF ConnUnitEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of units under a single SNMP agent. The number of entries is given by the value of uNumber. It is 1 for stand-alone system." ::= { connSet 6 } connUnitEntry OBJECT-TYPE SYNTAX ConnUnitEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A connectivity unit entry containing objects for a particular unit." INDEX { connUnitId } ::= { connUnitTable 1 } ConnUnitEntry ::= SEQUENCE { connUnitId OCTET STRING, connUnitGlobalId FcGlobalId, connUnitType FcUnitType, connUnitNumports INTEGER, connUnitState INTEGER, connUnitStatus INTEGER, connUnitProduct DisplayString, connUnitSn DisplayString, connUnitUpTime TimeTicks, connUnitUrl DisplayString, connUnitDomainId OCTET STRING, connUnitProxyMaster INTEGER, connUnitPrincipal INTEGER, connUnitNumSensors INTEGER, connUnitStatusChangeTime TimeTicks, connUnitConfigurationChangeTime TimeTicks, connUnitNumRevs INTEGER, connUnitNumZones INTEGER, connUnitModuleId OCTET STRING, connUnitName DisplayString, connUnitInfo DisplayString, connUnitControl INTEGER, connUnitContact DisplayString, connUnitLocation DisplayString, connUnitEventFilter FcEventSeverity, connUnitNumEvents INTEGER, connUnitMaxEvents INTEGER, connUnitEventCurrID INTEGER } connUnitId OBJECT-TYPE SYNTAX OCTET STRING (SIZE (16)) ACCESS read-only STATUS mandatory DESCRIPTION "The unique identification for this connectivity unit among those within this proxy domain. The value MUST be unique within the proxy domain because it is the index variable for connUnitTable. The value assigned to a given conectivity unit SHOULD be persistent across agent and unit resets. It SHOULD be the same as connUnitGlobalId if connUnitGlobalId is known and stable." ::= { connUnitEntry 1 } connUnitGlobalId OBJECT-TYPE SYNTAX FcGlobalId ACCESS read-only STATUS mandatory DESCRIPTION "An optional global-scope identifier for this connectivity unit. It MUST be a WWN for this connectivity unit or 16 octets of value zero. WWN formats requiring fewer than 16 octets MUST be extended to 16 octets with trailing zero octets, If a WWN is used for connUnitId, the same WWN MUST be used for connUnitGlobalId. When a non-zero value is provided, it SHOULD be persistent across agent and unit resets. It SHOULD be globally unique. It SHOULD be one of these FC-PH/PH3 formats: IEEE (NAA=1) IEEE Extended (NAA=2) IEEE Registered (NAA=5). IEEE Registered extended (NAA=6). Use of the IEEE formats allows any IEEE-registered vendor to assure global uniqueness independently. The following are some references on IEEE WWN formats: http://standards.ieee.org/regauth/oui/tutorials/fibreformat.html http://standards.ieee.org/regauth/oui/tutorials/fibrecomp_id.html If one or more WWNs are associated with the connUnit via other management methods, one of them SHOULD be used for connUnitGlobalId. If there is not a WWN assigned specifically to the connUnit, there is some merit, though not a requirement, to using a WWN assigned to (one of) its permanently attached FC/LAN interface(s). This can not risk uniqueness, though. As a counterexample, if your agent runs in a host and the host has an HBA, it is quite possible that agent, host, and HBA will all be distinct connUnits, so the host and agent can not use the WWN of the HBA. Another example: If your hub has a built-in Ethernet port, it might be reasonable for the hub to use its LAN address (prefixed with the appropriate NAA) as its connUnitId. But if the Ethernet were a replaceable PCCard, the hub should have an independent ID." ::= { connUnitEntry 2 } connUnitType OBJECT-TYPE SYNTAX FcUnitType ACCESS read-only STATUS mandatory DESCRIPTION "The type of this connectivity unit." ::= { connUnitEntry 3 } connUnitNumports OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of physical ports in the connectivity unit (internal/embedded, external)." ::= { connUnitEntry 4 } connUnitState OBJECT-TYPE SYNTAX INTEGER { unknown(1), online(2), offline(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Overall state of the connectivity unit." ::= { connUnitEntry 5 } connUnitStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), unused(2), ok(3), warning(4), -- needs attention failed(5) } ACCESS read-only STATUS mandatory DESCRIPTION "Overall status of the connectivity unit." ::= { connUnitEntry 6 } connUnitProduct OBJECT-TYPE SYNTAX DisplayString (SIZE (0..79)) ACCESS read-only STATUS mandatory DESCRIPTION "The connectivity unit vendor's product model name." ::= { connUnitEntry 7 } connUnitSn OBJECT-TYPE SYNTAX DisplayString (SIZE (0..79)) ACCESS read-only STATUS mandatory DESCRIPTION "The serial number for this connectivity unit." ::= { connUnitEntry 8 } connUnitUpTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "The number of centiseconds since the last unit initialization." ::= { connUnitEntry 9 } connUnitUrl OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "URL to launch a management application, if applicable. Otherwise empty string. In a standalone unit, this would be the same as the top-level URL. This has the same definition as systemURL for keywords." ::= { connUnitEntry 10 } connUnitDomainId OBJECT-TYPE SYNTAX OCTET STRING (SIZE(3)) ACCESS read-only STATUS mandatory DESCRIPTION "24 bit Fibre Channel address ID of this connectivity unit, right justified with leading zero's if required. If this value is not applicable, return all bits set to one." ::= { connUnitEntry 11 } connUnitProxyMaster OBJECT-TYPE SYNTAX INTEGER { unknown(1), no(2), yes(3) } ACCESS read-only STATUS mandatory DESCRIPTION "A value of 'yes' means this is the proxy master unit for a set of managed units. For example, this could be the only unit with a management card in it for a set of units. A standalone unit should return 'yes' for this object." ::= { connUnitEntry 12 } connUnitPrincipal OBJECT-TYPE SYNTAX INTEGER { unknown(1), no(2), yes(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Whether this connectivity unit is the principal unit within the group of fabric elements. If this value is not applicable, return unknown." ::= { connUnitEntry 13 } connUnitNumSensors OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of sensors in the connUnitSensorTable." ::= { connUnitEntry 14 } connUnitStatusChangeTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS deprecated DESCRIPTION "The sysuptime timestamp in centiseconds at which the last status change occurred." ::= { connUnitEntry 15 } connUnitConfigurationChangeTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS deprecated DESCRIPTION "The sysuptime timestamp in centiseconds at which the last configuration change occurred." ::= { connUnitEntry 16 } connUnitNumRevs OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of revisions in the connUnitRevsTable." DEFVAL { 1 } ::= { connUnitEntry 17 } connUnitNumZones OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS deprecated DESCRIPTION "Number of zones defined in connUnitZoneTable." ::= { connUnitEntry 18 } connUnitModuleId OBJECT-TYPE SYNTAX OCTET STRING (SIZE(16)) ACCESS read-only STATUS mandatory DESCRIPTION "This is a unique id, persistent between boots, that can be used to group a set of connUnits together into a module. The intended use would be to create a connUnit with a connUnitType of 'module' to represent a physical or logical group of connectivity units. Then the value of the group would be set to the value of connUnitId for this 'container' connUnit. connUnitModuleId should be zeros if this connUnit is not part of a module." ::= { connUnitEntry 19 } connUnitName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..79)) ACCESS read-write STATUS mandatory DESCRIPTION "A display string containing a name for this connectivity unit. This object value should be persistent between boots." ::= { connUnitEntry 20 } connUnitInfo OBJECT-TYPE SYNTAX DisplayString ACCESS read-write STATUS mandatory DESCRIPTION "A display string containing information about this connectivity unit. This object value should be persistent between boots." ::= { connUnitEntry 21 } connUnitControl OBJECT-TYPE SYNTAX INTEGER { unknown(1), invalid(2), resetConnUnitColdStart(3), resetConnUnitWarmStart(4), offlineConnUnit(5), onlineConnUnit(6) } ACCESS read-write STATUS mandatory DESCRIPTION "This object is used to control the addressed connUnit. NOTE: 'Cold Start' and 'Warm Start' are as defined in MIB II and are not meant to be a factory reset. resetConnUnitColdStart: the addressed unit performs a 'Cold Start' reset. resetConnUnitWarmStart: the addressed unit performs a 'Warm Start' reset. offlineConnUnit: the addressed unit puts itself into an implementation dependant 'offline' state. In general,if a unit is in an offline state, it cannot be used to perform meaningful Fibre Channel work. onlineConnUnit: the addressed unit puts itself into an implementation dependant 'online' state. In general, if a unit is in an online state, it is capable of performing meaningful Fibre Channel work. NOTE: Each implementation may chose not to allow any or all of these values on a SET. " ::= { connUnitEntry 22 } connUnitContact OBJECT-TYPE SYNTAX DisplayString (SIZE (0..79)) ACCESS read-write STATUS mandatory DESCRIPTION "Contact information for this connectivity unit." ::= { connUnitEntry 23 } connUnitLocation OBJECT-TYPE SYNTAX DisplayString (SIZE (0..79)) ACCESS read-write STATUS mandatory DESCRIPTION "Location information for this connectivity unit." ::= { connUnitEntry 24 } connUnitEventFilter OBJECT-TYPE SYNTAX FcEventSeverity ACCESS read-only STATUS mandatory DESCRIPTION "This value defines the event severity that will be logged by this connectivity unit. All events of severity less than or equal to connUnitEventFilter are logged in connUnitEventTable." ::= { connUnitEntry 25 } connUnitNumEvents OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of events currently in the connUnitEventTable." ::= { connUnitEntry 26 } connUnitMaxEvents OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Max number of events that can be defined in connUnitEventTable." ::= { connUnitEntry 27 } connUnitEventCurrID OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The last used event id (connUnitEventId)." ::= { connUnitEntry 28 } ------------------------------------------------------------------ -- The Table of revisions for hardware and software elements. connUnitRevsTable OBJECT-TYPE SYNTAX SEQUENCE OF ConnUnitRevsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table of the revisions supported by connectivity units managed by this agent." ::= { connSet 7 } connUnitRevsEntry OBJECT-TYPE SYNTAX ConnUnitRevsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "" INDEX { connUnitRevsUnitId, connUnitRevsIndex } ::= { connUnitRevsTable 1 } ConnUnitRevsEntry ::= SEQUENCE { connUnitRevsUnitId OCTET STRING, connUnitRevsIndex INTEGER, connUnitRevsRevId DisplayString, connUnitRevsDescription DisplayString } connUnitRevsUnitId OBJECT-TYPE SYNTAX OCTET STRING (SIZE (16)) ACCESS read-only STATUS mandatory DESCRIPTION "The connUnitId of the connectivity unit that contains this revision table." ::= { connUnitRevsEntry 1 } connUnitRevsIndex OBJECT-TYPE SYNTAX INTEGER (1..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "A unique value among all connUnitRevsEntrys with the same value of connUnitRevsUnitId, in the range between 1 and connUnitNumRevs[connUnitRevsUnitId]." ::= { connUnitRevsEntry 2 } connUnitRevsRevId OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "A vendor-specific string identifying a revision of a component of the connUnit indexed by connUnitRevsUnitId." ::= { connUnitRevsEntry 3 } connUnitRevsDescription OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Description of a component to which the revision corresponds." ::= { connUnitRevsEntry 4 } ----------------------------------------------------------------------- -- The Sensor table connUnitSensorTable OBJECT-TYPE SYNTAX SEQUENCE OF ConnUnitSensorEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table of the sensors supported by each connectivity unit managed by this agent." ::= { connSet 8 } connUnitSensorEntry OBJECT-TYPE SYNTAX ConnUnitSensorEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry contains the information for a specific sensor." INDEX { connUnitSensorUnitId, connUnitSensorIndex } ::= { connUnitSensorTable 1 } ConnUnitSensorEntry ::= SEQUENCE { connUnitSensorUnitId OCTET STRING, connUnitSensorIndex INTEGER (1..2147483647), connUnitSensorName DisplayString, connUnitSensorStatus INTEGER, connUnitSensorInfo DisplayString, connUnitSensorMessage DisplayString, connUnitSensorType INTEGER, connUnitSensorCharacteristic INTEGER } connUnitSensorUnitId OBJECT-TYPE SYNTAX OCTET STRING (SIZE (16)) ACCESS read-only STATUS mandatory DESCRIPTION "The connUnitId of the connectivity unit that contains this sensor table." ::= { connUnitSensorEntry 1 } connUnitSensorIndex OBJECT-TYPE SYNTAX INTEGER (1..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "A unique value among all connUnitSensorEntrys with the same value of connUnitSensorUnitId, in the range between 1 and connUnitNumSensor[connUnitSensorUnitId]." ::= { connUnitSensorEntry 2} connUnitSensorName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "A textual identification of the sensor intended primarily for operator use." ::= { connUnitSensorEntry 3 } connUnitSensorStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), other(2), ok(3), -- the sensor indicates ok warning(4), -- the sensor indicates a warning failed(5) -- the sensor indicates failure } ACCESS read-only STATUS mandatory DESCRIPTION "The status indicated by the sensor." ::= { connUnitSensorEntry 4 } connUnitSensorInfo OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Miscellaneous static info about the sensor such as its serial number." ::= { connUnitSensorEntry 5 } connUnitSensorMessage OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "This describes the status of the sensor as a message. It may also provide more resolution on the sensor indication, for example 'Cover temperature 1503K, above nominal operating range'" ::= { connUnitSensorEntry 6 } connUnitSensorType OBJECT-TYPE SYNTAX INTEGER { unknown(1), other(2), battery(3), fan(4), power-supply(5), transmitter(6), enclosure(7), board(8), receiver(9) } ACCESS read-only STATUS mandatory DESCRIPTION "The type of component being monitored by this sensor." ::= { connUnitSensorEntry 7 } connUnitSensorCharacteristic OBJECT-TYPE SYNTAX INTEGER { unknown(1), other(2), temperature(3), pressure(4), emf(5), currentValue(6), -- current is a keyword airflow(7), frequency(8), power(9) } ACCESS read-only STATUS mandatory DESCRIPTION "The characteristics being monitored by this sensor." ::= { connUnitSensorEntry 8 } ----------------------------------------------------------------------- -- The port table connUnitPortTable OBJECT-TYPE SYNTAX SEQUENCE OF ConnUnitPortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Generic information on ports for a specific connUnit." ::= { connSet 10 } connUnitPortEntry OBJECT-TYPE SYNTAX ConnUnitPortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry contains the information for a specific port." INDEX { connUnitPortUnitId, connUnitPortIndex } ::= { connUnitPortTable 1 } ConnUnitPortEntry ::= SEQUENCE { connUnitPortUnitId OCTET STRING, connUnitPortIndex INTEGER, connUnitPortType INTEGER, connUnitPortFCClassCap OCTET STRING, connUnitPortFCClassOp OCTET STRING, connUnitPortState INTEGER, connUnitPortStatus INTEGER, connUnitPortTransmitterType INTEGER, connUnitPortModuleType INTEGER, connUnitPortWwn FcNameId, connUnitPortFCId OCTET STRING, connUnitPortSn DisplayString, connUnitPortRevision DisplayString, connUnitPortVendor DisplayString, connUnitPortSpeed INTEGER, connUnitPortControl INTEGER, connUnitPortName DisplayString, connUnitPortPhysicalNumber INTEGER, connUnitPortStatObject OBJECT IDENTIFIER } connUnitPortUnitId OBJECT-TYPE SYNTAX OCTET STRING (SIZE (16)) ACCESS read-only STATUS mandatory DESCRIPTION "The connUnitId of the connectivity unit that contains this port." ::= { connUnitPortEntry 1 } connUnitPortIndex OBJECT-TYPE SYNTAX INTEGER (1..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "A unique value among all connUnitPortEntrys on this connectivity unit, between 0 and connUnitNumPort[connUnitPortUnitId]." ::= { connUnitPortEntry 2 } connUnitPortType OBJECT-TYPE SYNTAX INTEGER { unknown (1), other (2), not-present (3), hub-port (4), n-port (5), -- end port for fabric l-port (6), -- end port for loop fl-port (7), -- public loop f-port (8), -- fabric port e-port (9), -- fabric expansion port g-port (10), -- generic fabric port domain-ctl (11), -- domain controller hub-controller(12), scsi (13), -- parallel SCSI port escon (14), lan (15), wan (16) } ACCESS read-only STATUS mandatory DESCRIPTION "The port type." ::= { connUnitPortEntry 3 } connUnitPortFCClassCap OBJECT-TYPE SYNTAX OCTET STRING (SIZE (2)) ACCESS read-only STATUS mandatory DESCRIPTION "Bit mask that specifies the classes of service capability of this port. If this is not applicable, return all bits set to zero. The bits have the following definition: unknown - 0 class-f - 1 class-one - 2 class-two - 4 class-three - 8 class-four - 16 class-five - 32 class-six - 64" ::= { connUnitPortEntry 4 } connUnitPortFCClassOp OBJECT-TYPE SYNTAX OCTET STRING (SIZE (2)) ACCESS read-only STATUS mandatory DESCRIPTION "Bit mask that specifies the classes of service that are currently operational. If this is not applicable, return all bits set to zero. This object has the same definition as connUnitPortFCClassCap" ::= { connUnitPortEntry 5 } connUnitPortState OBJECT-TYPE SYNTAX INTEGER { unknown(1), online(2), offline(3), bypassed(4) } ACCESS read-only STATUS mandatory DESCRIPTION "The state of the port hardware." ::= { connUnitPortEntry 6 } connUnitPortStatus OBJECT-TYPE SYNTAX INTEGER { unknown (1), unused (2), ok (3), warning (4), -- needs attention failure (5), notparticipating (6), initializing(7), bypass (8) -- manually or automatically -- isolated from loop or fabric } ACCESS read-only STATUS mandatory DESCRIPTION "An overall protocol status for the port." ::= { connUnitPortEntry 7 } connUnitPortTransmitterType OBJECT-TYPE SYNTAX INTEGER { unknown(1), other(2), unused(3), shortwave(4), longwave(5), copper(6), scsi(7), longwaveNoOFC(8), shortwaveNoOFC(9), longwaveLED(10) } ACCESS read-only STATUS mandatory DESCRIPTION "The technology of the port transceiver." ::= { connUnitPortEntry 8 } connUnitPortModuleType OBJECT-TYPE SYNTAX INTEGER { unknown(1), other(2), gbic(3), embedded(4), -- fixed, ie, oneXnine glm(5), gbicSerialId(6), gbicNoSerialId(7), gbicNotInstalled(8), smallFormFactor(9) } ACCESS read-only STATUS mandatory DESCRIPTION "The module type of the port connector." ::= { connUnitPortEntry 9 } connUnitPortWwn OBJECT-TYPE SYNTAX FcNameId ACCESS read-only STATUS mandatory DESCRIPTION "The World Wide Name of the port if applicable, otherwise empty string." ::= { connUnitPortEntry 10 } connUnitPortFCId OBJECT-TYPE SYNTAX OCTET STRING (SIZE(3)) ACCESS read-only STATUS mandatory DESCRIPTION "This is the assigned Fibre Channel ID of this port. This value is expected to be a Big Endian value of 24 bits. If this is loop, then it is the ALPA that is connected. If this is an eport, then it will only contain the domain ID left justified, zero filled. If this port does not have a Fibre Channel address, return all bits set to 1." ::= { connUnitPortEntry 11 } connUnitPortSn OBJECT-TYPE SYNTAX DisplayString (SIZE(0..79)) ACCESS read-only STATUS mandatory DESCRIPTION "The serial number of the unit (e.g., for a GBIC). If this is not applicable, return empty string." ::= { connUnitPortEntry 12 } connUnitPortRevision OBJECT-TYPE SYNTAX DisplayString (SIZE(0..79)) ACCESS read-only STATUS mandatory DESCRIPTION "The port revision (e.g., for a GBIC)." ::= { connUnitPortEntry 13 } connUnitPortVendor OBJECT-TYPE SYNTAX DisplayString (SIZE(0..79)) ACCESS read-only STATUS mandatory DESCRIPTION "The port vendor (e.g., for a GBIC)." ::= { connUnitPortEntry 14 } connUnitPortSpeed OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The speed of the port in kilobytes per second." ::= { connUnitPortEntry 15 } connUnitPortControl OBJECT-TYPE SYNTAX INTEGER { unknown(1), invalid(2), resetConnUnitPort(3), bypassConnUnitPort(4), unbypassConnUnitPort(5), offlineConnUnitPort(6), onlineConnUnitPort(7), resetConnUnitPortCounters(8) } ACCESS read-write -- (or maybe write-only) STATUS mandatory DESCRIPTION "This object is used to control the addressed connUnit's port. Valid commands are: resetConnUnitPort: If the addressed connUnit allows this operation to be performed to this port, the addressed port performs a vendor-specific 'reset' operation. Examples of these operations are: the Link Reset protocol, the Loop Initialization protocol, or a resynchronization occurring between the transceiver in the addressed port to the transceiver that the port is connected to. bypassConnUnitPort: If the addressed connUnit allows this operation to be performed to this port, the addressed port performs a vendor-specific 'bypass' operation. Examples of these operations are: transitioning from online to offline, a request(NON-PARTICIPATING) command to the Loop Port state machine, or removal of the port from an arbitrated loop by a hub. unbypassConnUnitPort: If the addressed connUnit allows this operation to be performed to this port, the addressed port performs a vendor-specific 'unbypass' operation. Examples of these operations are: the Link Failure protocol, a request(PARTICIPATING) command to the Loop Port state machine, or addition of the port to an arbitrated loop by a hub. offlineConnUnitPort: If the addressed connUnit allows this operation to be performed to this port, the addressed port performs a vendor-specific 'offline' operation. Examples of these operations are: disabling a port's transceiver, the Link Failure protocol, request(NON-PARTICIPATING) command to the Loop Port state machine, or removal of the port from an arbitrated loop by a hub. onlineConnUnitPort: If the addressed connUnit allows this operation to be performed to this port, the addressed port performs a vendor-specific 'online' operation. Examples of these operations are: enabling a port's transceiver, the Link Failure protocol, request(PARTICIPATING) command to the Loop Port state machine, or addition of the port from an arbitrated loop by a hub. NOTE: Each implementation may chose not to allow any or all of these values on a SET. " ::= { connUnitPortEntry 16 } connUnitPortName OBJECT-TYPE SYNTAX DisplayString ACCESS read-write STATUS mandatory DESCRIPTION "A string describing the addressed port." ::= { connUnitPortEntry 17 } connUnitPortPhysicalNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This is the internal port number this port is known by. In many implementations, this should be the same as connUnitPortIndex. Some implementations may have an internal port representation not compatible with the rules for table indeces. In that case, provide the internal representation of this port in this object. This value may also be used in the connUnitLinkPortNumberX or connUnitLinkPortNumberY objects of the connUnitLinkTable." ::= { connUnitPortEntry 18 } connUnitPortStatObject OBJECT-TYPE SYNTAX OBJECT IDENTIFIER ACCESS read-only STATUS mandatory DESCRIPTION "This contains the OID of the first object of the table that contains the statistics for this particular port. If this has a value of zero, then there are no statistics available for this port. The port type information will help identify the statistics objects that will be found in the table. From this point, one would do a getnext to get the next statistics object. When the first part of the OID changes, the end of table is reached." ::= { connUnitPortEntry 19 } ----------------------------------------------------------------------- -- event group connUnitEventTable OBJECT-TYPE SYNTAX SEQUENCE OF ConnUnitEventEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table of connectivity unit events. Errors, warnings, and information should be reported in this table." ::= { connSet 11 } connUnitEventEntry OBJECT-TYPE SYNTAX ConnUnitEventEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry contains information on a specific event for the given connectivity unit." INDEX { connUnitEventUnitId, connUnitEventIndex } ::= { connUnitEventTable 1 } ConnUnitEventEntry ::= SEQUENCE { connUnitEventUnitId OCTET STRING, connUnitEventIndex INTEGER (1..2147483647), connUnitEventId INTEGER, connUnitREventTime DisplayString, connUnitSEventTime TimeTicks, connUnitEventSeverity FcEventSeverity, connUnitEventType INTEGER, connUnitEventObject OBJECT IDENTIFIER, connUnitEventDescr DisplayString } connUnitEventUnitId OBJECT-TYPE SYNTAX OCTET STRING (SIZE (16)) ACCESS read-only STATUS mandatory DESCRIPTION "The connUnitId of the connectivity unit that contains this event table." ::= { connUnitEventEntry 1 } connUnitEventIndex OBJECT-TYPE SYNTAX INTEGER (1..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Each connectivity unit has its own event buffer. As it wraps, it may write over previous events. This object is an index into the buffer. It is recommended that this table be read using 'getNext's to retrieve the initial table. The management application should read the event table at periodic intervals and then determine if any new entries were added by comparing the last known index value with the current highest index value. The management application should then update its copy of the event table. If the read interval is too long, it is possible that there may be events that may not be contained in the agent's internal event buffer. For example, an agent may read events 50-75. At the next read interval, connUnitEventCurrID is 189. If the management app tries to read event index 76, and the agent's internal buffer is 100 entries max, event index 76 will no longer be available. The index value is an incrementing integer starting from one every time there is a table reset. On table reset, all contents are emptied and all indeces are set to zero. When an event is added to the table, the event is assigned the next higher integer value than the last item entered into the table. If the index value reaches its maximum value, the next item entered will cause the index value to roll over and start at one again." ::= { connUnitEventEntry 2 } connUnitEventId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS deprecated DESCRIPTION "The internal event Id. Incremented for each event, ranging between 0 and connUnitMaxEvents. Not used as table index to simplify the agent implementation. When this reaches the end of the range specified by connUnitMaxEvents, the Id will roll over to start at zero. This value will be set back to zero at reset. The relationship of this value to the index is that internal event id may represent a smaller number than a 32 bit integer (eg max 100 entries) and would only have a value range up to connUnitMaxEvents." ::= { connUnitEventEntry 3 } connUnitREventTime OBJECT-TYPE SYNTAX DisplayString (SIZE (15)) ACCESS read-only STATUS mandatory DESCRIPTION "This is the real time when the event occurred. It has the following format. DDMMYYYY HHMMSS DD=day number MM=month number YYYY=year number HH=hour number MM=minute number SS=seconds number If not applicable, return a NULL string." ::= { connUnitEventEntry 4 } connUnitSEventTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "This is the sysuptime timestamp when the event occurred." ::= { connUnitEventEntry 5 } connUnitEventSeverity OBJECT-TYPE SYNTAX FcEventSeverity ACCESS read-only STATUS mandatory DESCRIPTION "The event severity level." ::= { connUnitEventEntry 6 } connUnitEventType OBJECT-TYPE SYNTAX INTEGER { unknown(1), other(2), status(3), configuration(4), topology(5) } ACCESS read-only STATUS mandatory DESCRIPTION "The type of this event." ::= { connUnitEventEntry 7 } connUnitEventObject OBJECT-TYPE SYNTAX OBJECT IDENTIFIER ACCESS read-only STATUS mandatory DESCRIPTION "This is used with the connUnitEventType to identify which object the event refers to. It can be the OID of a connectivity unit or of another object like connUnitPortStatus[...]" ::= { connUnitEventEntry 8 } connUnitEventDescr OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The description of the event." ::= { connUnitEventEntry 9 } -- The link table -- is intended to organize and communicate -- any information the agent possesses -- which would assist a management application -- to discover the CONNECTIVITY UNITS in the -- framework and the TOPOLOGY of their interconnect. -- That is, the goal is to assist the management -- application not only to LIST the elements of the framework, -- but to MAP them. -- With this goal, the agent SHOULD include -- as much as it possesses about any links -- from its own connectivity units to others, -- including links among its own units. -- An agent SHOULD include partial information -- about links if it is not able to fully -- define them in accord with the following structure; -- however, the information MUST include either -- a nonzero connUnitNodeId- or a nonzero connUnitPortWwn- -- for each end of the link. -- If the agent is able to discover links -- which do not directly attach to members of its agency -- and its discovery algorithm gives some assurance -- the links are recently valid, it MAY include these links. -- Link information entered by administrative action -- MAY be included even if not validated directly -- if the link has at least one endpoint in this agency, -- but SHOULD NOT be included otherwise. -- A connectivity unit should fill the table in as best it can. -- One of the methods to fill this in would be to use the RNID -- ELS (ANSI document 99-422v0). This allows one to query a -- port for the information needed for the link table. -- This table is accessed either directly if the management -- software has an index value or via GetNexts. The value of -- the indexes are not required to be contiguous. Each entry -- created in this table will be assigned an index. This -- relationship is kept persistent until the entry is removed -- from the table or the system is reset. The total number of -- entries are defined by the size of the table -- For an entry to be considered to be valid, both the X (local) -- and the Y (remote) need to have one valid value. connUnitLinkTable OBJECT-TYPE SYNTAX SEQUENCE OF ConnUnitLinkEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of links know to this agent from this connectivity unit to other connectivity units." ::= { connSet 12 } connUnitLinkEntry OBJECT-TYPE SYNTAX ConnUnitLinkEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry describing a particular link to another." INDEX { connUnitLinkUnitId, connUnitLinkIndex } ::= { connUnitLinkTable 1 } ConnUnitLinkEntry ::= SEQUENCE { connUnitLinkUnitId OCTET STRING, connUnitLinkIndex INTEGER, connUnitLinkNodeIdX OCTET STRING, connUnitLinkPortNumberX INTEGER, connUnitLinkPortWwnX OCTET STRING, connUnitLinkNodeIdY OCTET STRING, connUnitLinkPortNumberY INTEGER, connUnitLinkPortWwnY OCTET STRING, connUnitLinkAgentAddressY OCTET STRING, connUnitLinkAgentAddressTypeY INTEGER, connUnitLinkAgentPortY INTEGER, connUnitLinkUnitTypeY FcUnitType, connUnitLinkConnIdY OCTET STRING } connUnitLinkUnitId OBJECT-TYPE SYNTAX OCTET STRING (SIZE (16)) ACCESS read-only STATUS mandatory DESCRIPTION "The connUnitId of the connectivity unit that contains this link table." ::= { connUnitLinkEntry 1 } connUnitLinkIndex OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "This value is used to create a unique value for each entry in the link table with the same connUnitLinkUnitId. The value can only be reused if it is not currently in in use and the value is the next candidate to be used. This value is allowed to wrap at the highest value represented by the number of bits. This value is reset to zero when the system is Reset and the first value to be used is one." ::= { connUnitLinkEntry 2 } connUnitLinkNodeIdX OBJECT-TYPE SYNTAX OCTET STRING (SIZE(64)) ACCESS read-only STATUS mandatory DESCRIPTION "The node WWN of the unit at one end of the link. If the node WWN is unknown and the node is a connUnit in the responding agent then the value of this object MUST BE equal to its connUnitID." ::= { connUnitLinkEntry 3 } connUnitLinkPortNumberX OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The port number on the unit specified by connUnitLinkNodeIdX if known, otherwise -1. If the value is nonnegative then it will be equal to connUnitPortPhysicalNumber." ::= { connUnitLinkEntry 4 } connUnitLinkPortWwnX OBJECT-TYPE SYNTAX OCTET STRING (SIZE(16)) ACCESS read-only STATUS mandatory DESCRIPTION "The port WWN of the unit specified by connUnitLinkNodeIdX if known, otherwise 16 octets of binary 0" ::= { connUnitLinkEntry 5 } connUnitLinkNodeIdY OBJECT-TYPE SYNTAX OCTET STRING (SIZE(64)) ACCESS read-only STATUS mandatory DESCRIPTION "The node WWN of the unit at the other end of the link. If the node WWN is unknown and the node is a connUnit in the responding SNMP agency then the value of this object MUST BE equal to its connUnitID." ::= { connUnitLinkEntry 6 } connUnitLinkPortNumberY OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The port number on the unit specified by connUnitLinkNodeIdY if known, otherwise -1. If the value is nonnegative then it will be equal to connUnitPortPhysicalNumber." ::= { connUnitLinkEntry 7 } connUnitLinkPortWwnY OBJECT-TYPE SYNTAX OCTET STRING (SIZE(16)) ACCESS read-only STATUS mandatory DESCRIPTION "The port WWN on the unit specified by connUnitLinkNodeIdY if known, otherwise 16 octets of binary 0" ::= { connUnitLinkEntry 8 } connUnitLinkAgentAddressY OBJECT-TYPE SYNTAX OCTET STRING (SIZE(16)) ACCESS read-only STATUS mandatory DESCRIPTION "The address of an FCMGMT MIB agent for the node identified by connUnitLinkNodeIdY, if known; otherwise 16 octets of binary 0" ::= { connUnitLinkEntry 9 } connUnitLinkAgentAddressTypeY OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "If connUnitLinkAgentAddressY is nonzero, it is a protocol address. ConnUnitLinkAgentAddressTypeY is the the 'address family number' assigned by IANA to identify the address format. (eg, 1 is Ipv4, 2 is Ipv6)." ::= { connUnitLinkEntry 10 } connUnitLinkAgentPortY OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The IP port number for the agent. This is provided in case the agent is at a non-standard SNMP port." ::= { connUnitLinkEntry 11 } connUnitLinkUnitTypeY OBJECT-TYPE SYNTAX FcUnitType ACCESS read-only STATUS mandatory DESCRIPTION "Type of the FC connectivity unit as defined in connUnitType." ::= { connUnitLinkEntry 12 } connUnitLinkConnIdY OBJECT-TYPE SYNTAX OCTET STRING (SIZE(3)) ACCESS read-only STATUS mandatory DESCRIPTION "This is the Fibre Channel ID of this port. If the connectivity unit is a switch, this is expected to be a Big Endian value of 24 bits. If this is loop, then it is the ALPA that is connected. If this is an eport, then it will only contain the domain ID. If not any of those, unknown or cascaded loop, return all bits set to 1." ::= { connUnitLinkEntry 13 } ------------------------------------------------------------------------------ -- The following is a set of statistics tables. There is one for each port -- type class. Port types are aggregated into a port type class, such as all -- the fabric port types. There is one and only one statistics table for each -- individual port. For all objects in statistics tables, if the object is not -- supported by the conn unit then the high order bit is set to 1 with all other -- bits set to zero. The high order bit is reserved to indicate is the object -- if supported or not. All objects start at a value of zero at hardware initialization -- and continue incrementing till end of 63 bits and then wrap to zero. -- Hub Port Statistics connUnitPortStatHubTable OBJECT-TYPE SYNTAX SEQUENCE OF ConnUnitPortStatHubEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of statistics for the hub port type." ::= { statSet 1 } connUnitPortStatHubEntry OBJECT-TYPE SYNTAX ConnUnitPortStatHubEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry describing port statistics." INDEX { connUnitPortStatHubUnitId, connUnitPortStatHubIndex } ::= { connUnitPortStatHubTable 1 } ConnUnitPortStatHubEntry ::= SEQUENCE { connUnitPortStatHubUnitId OCTET STRING, connUnitPortStatHubIndex INTEGER, connUnitPortStatHubCountError OCTET STRING, connUnitPortStatHubCountTxFrame OCTET STRING, connUnitPortStatHubCountRxFrame OCTET STRING, connUnitPortStatHubCountTxOctets OCTET STRING, connUnitPortStatHubCountRxOctets OCTET STRING } connUnitPortStatHubUnitId OBJECT-TYPE SYNTAX OCTET STRING (SIZE (16)) ACCESS read-only STATUS mandatory DESCRIPTION "The connUnitId of the connectivity unit that contains this port stat table." ::= { connUnitPortStatHubEntry 1 } connUnitPortStatHubIndex OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "A unique value among all entrys in this table, between 0 and connUnitNumPort[connUnitPortUnitId]." ::= { connUnitPortStatHubEntry 2 } connUnitPortStatHubCountError OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "A count of the errors that have occured on this port." ::= { connUnitPortStatHubEntry 3 } connUnitPortStatHubCountTxFrame OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames that have been transmitted by this port." ::= { connUnitPortStatHubEntry 4 } connUnitPortStatHubCountRxFrame OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames that have been received by this port." ::= { connUnitPortStatHubEntry 5 } connUnitPortStatHubCountTxOctets OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "The number of octets that have been transmitted by this port." ::= { connUnitPortStatHubEntry 6 } connUnitPortStatHubCountRxOctets OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "The number of octets that have been received. by this port." ::= { connUnitPortStatHubEntry 7 } -- Fabric Port Statistics connUnitPortStatFabricTable OBJECT-TYPE SYNTAX SEQUENCE OF ConnUnitPortStatFabricEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of statistics for the fabric port types." ::= { statSet 2 } connUnitPortStatFabricEntry OBJECT-TYPE SYNTAX ConnUnitPortStatFabricEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry describing port statistics." INDEX { connUnitPortStatFabricUnitId, connUnitPortStatFabricIndex } ::= { connUnitPortStatFabricTable 1 } ConnUnitPortStatFabricEntry ::= SEQUENCE { connUnitPortStatFabricUnitId OCTET STRING, connUnitPortStatFabricIndex INTEGER, connUnitPortStatFabricCountError OCTET STRING, connUnitPortStatFabricCountTxFrame OCTET STRING, connUnitPortStatFabricCountRxFrame OCTET STRING, connUnitPortStatFabricCountTxOctets OCTET STRING, connUnitPortStatFabricCountRxOctets OCTET STRING } connUnitPortStatFabricUnitId OBJECT-TYPE SYNTAX OCTET STRING (SIZE (16)) ACCESS read-only STATUS mandatory DESCRIPTION "The connUnitId of the connectivity unit that contains this port stat table." ::= { connUnitPortStatFabricEntry 1 } connUnitPortStatFabricIndex OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "A unique value among all entrys in this table, between 0 and connUnitNumPort[connUnitPortUnitId]." ::= { connUnitPortStatFabricEntry 2 } connUnitPortStatFabricCountError OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "A count of the errors that have occured on this port." ::= { connUnitPortStatFabricEntry 3 } connUnitPortStatFabricCountTxFrame OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames that have been transmitted by this port." ::= { connUnitPortStatFabricEntry 4 } connUnitPortStatFabricCountRxFrame OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames that have been received by this port." ::= { connUnitPortStatFabricEntry 5 } connUnitPortStatFabricCountTxOctets OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "The number of octets that have been transmitted by this port." ::= { connUnitPortStatFabricEntry 6 } connUnitPortStatFabricCountRxOctets OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "The number of octets that have been received. by this port." ::= { connUnitPortStatFabricEntry 7 } -- SCSI Port Statistics connUnitPortStatSCSITable OBJECT-TYPE SYNTAX SEQUENCE OF ConnUnitPortStatSCSIEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of statistics for the SCSI port type." ::= { statSet 3 } connUnitPortStatSCSIEntry OBJECT-TYPE SYNTAX ConnUnitPortStatSCSIEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry describing port statistics." INDEX { connUnitPortStatSCSIUnitId, connUnitPortStatSCSIIndex } ::= { connUnitPortStatSCSITable 1 } ConnUnitPortStatSCSIEntry ::= SEQUENCE { connUnitPortStatSCSIUnitId OCTET STRING, connUnitPortStatSCSIIndex INTEGER, connUnitPortStatSCSICountError OCTET STRING, connUnitPortStatSCSICountTxIO OCTET STRING, connUnitPortStatSCSICountRxIO OCTET STRING, connUnitPortStatSCSICountTxBytes OCTET STRING, connUnitPortStatSCSICountRxBytes OCTET STRING } connUnitPortStatSCSIUnitId OBJECT-TYPE SYNTAX OCTET STRING (SIZE (16)) ACCESS read-only STATUS mandatory DESCRIPTION "The connUnitId of the connectivity unit that contains this port stat table." ::= { connUnitPortStatSCSIEntry 1 } connUnitPortStatSCSIIndex OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "A unique value among all entrys in this table, between 0 and connUnitNumPort[connUnitPortUnitId]." ::= { connUnitPortStatSCSIEntry 2 } connUnitPortStatSCSICountError OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "A count of the errors that have occured on this port." ::= { connUnitPortStatSCSIEntry 3 } connUnitPortStatSCSICountTxIO OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "The number of I/Os that have been transmitted by this port." ::= { connUnitPortStatSCSIEntry 4 } connUnitPortStatSCSICountRxIO OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "The number of I/Os that have been received by this port." ::= { connUnitPortStatSCSIEntry 5 } connUnitPortStatSCSICountTxBytes OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "The number of bytes that have been transmitted by this port." ::= { connUnitPortStatSCSIEntry 6 } connUnitPortStatSCSICountRxBytes OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "The number of bytes that have been received. by this port." ::= { connUnitPortStatSCSIEntry 7 } -- LAN/WAN Port Statistics connUnitPortStatLANTable OBJECT-TYPE SYNTAX SEQUENCE OF ConnUnitPortStatLANEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of statistics for the LAN/WAN port type." ::= { statSet 4 } connUnitPortStatLANEntry OBJECT-TYPE SYNTAX ConnUnitPortStatLANEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry describing port statistics." INDEX { connUnitPortStatLANUnitId, connUnitPortStatLANIndex } ::= { connUnitPortStatLANTable 1 } ConnUnitPortStatLANEntry ::= SEQUENCE { connUnitPortStatLANUnitId OCTET STRING, connUnitPortStatLANIndex INTEGER, connUnitPortStatLANCountError OCTET STRING, connUnitPortStatLANCountTxPacket OCTET STRING, connUnitPortStatLANCountRxPacket OCTET STRING, connUnitPortStatLANCountTxBytes OCTET STRING, connUnitPortStatLANCountRxBytes OCTET STRING } connUnitPortStatLANUnitId OBJECT-TYPE SYNTAX OCTET STRING (SIZE (16)) ACCESS read-only STATUS mandatory DESCRIPTION "The connUnitId of the connectivity unit that contains this port stat table." ::= { connUnitPortStatLANEntry 1 } connUnitPortStatLANIndex OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "A unique value among all entrys in this table, between 0 and connUnitNumPort[connUnitPortUnitId]." ::= { connUnitPortStatLANEntry 2 } connUnitPortStatLANCountError OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "A count of the errors that have occured on this port." ::= { connUnitPortStatLANEntry 3 } connUnitPortStatLANCountTxPacket OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "The number of packets that have been transmitted by this port." ::= { connUnitPortStatLANEntry 4 } connUnitPortStatLANCountRxPacket OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "The number of packets that have been received by this port." ::= { connUnitPortStatLANEntry 5 } connUnitPortStatLANCountTxBytes OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "The number of bytes that have been transmitted by this port." ::= { connUnitPortStatLANEntry 6 } connUnitPortStatLANCountRxBytes OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) ACCESS read-only STATUS mandatory DESCRIPTION "The number of bytes that have been received. by this port." ::= { connUnitPortStatLANEntry 7 } ----------------------------------------------------------------------- -- SNMP trap registration group trapMaxClients OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of SNMP trap recipients supported by the connectivity unit." ::= { trapReg 1 } trapClientCount OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The current number of rows in the trap table." ::= { trapReg 2 } trapRegTable OBJECT-TYPE SYNTAX SEQUENCE OF TrapRegEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing a row for each IP address/port number that traps will be sent to." ::= { trapReg 3 } trapRegEntry OBJECT-TYPE SYNTAX TrapRegEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Ip/Port pair for a specific client." INDEX { trapRegIpAddress, trapRegPort } ::= { trapRegTable 1 } TrapRegEntry ::= SEQUENCE { trapRegIpAddress IpAddress, trapRegPort INTEGER (1..2147483647), trapRegFilter FcEventSeverity, trapRegRowState INTEGER } trapRegIpAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The Ip address of a client registered for traps." ::= { trapRegEntry 1 } trapRegPort OBJECT-TYPE SYNTAX INTEGER (1..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "The UDP port to send traps to for this host. Normally this would be the standard trap port (162). This object is an index and must be specified to create a row in this table." ::= { trapRegEntry 2 } trapRegFilter OBJECT-TYPE SYNTAX FcEventSeverity ACCESS read-write STATUS mandatory DESCRIPTION "This value defines the trap severity filter for this trap host. The connUnit will send traps to this host that have a severity level less than or equal to this value. The default value of this object is 'warning'." ::= { trapRegEntry 3} trapRegRowState OBJECT-TYPE SYNTAX INTEGER { rowDestroy(1), -- Remove row from table. rowInactive(2), -- Row exists, but TRAPs disabled rowActive(3) -- Row exists and is enabled for -- sending traps } ACCESS read-write STATUS mandatory DESCRIPTION "Specifies the state of the row. rowDestroy READ: Can never happen. WRITE: Remove this row from the table. rowInactive READ: Indicates that this row does exist, but that traps are not enabled to be sent to the target. WRITE: If the row does not exist, and the agent allows writes to the trap table, then a new row is created. The values of the optional columns will be set to default values. Traps are not enabled to be sent to the target. If the row already existed, then traps are disabled from being sent to the target. rowActive READ: Indicates that this row exists, and that traps are enabled to be sent to the target. WRITE: If the row does not exist, and the agent allows writes to the trap table, then a new row is created. The values of the optional columns will be set to default values. Traps are enabled to be sent to the target. If the row already exists, then traps are enabled to be sent to the target. A value of rowActive or rowInactive must be specified to create a row in the table." ::= { trapRegEntry 4} -- Related traps connUnitStatusChange TRAP-TYPE ENTERPRISE fcmgmt VARIABLES { connUnitStatus, connUnitState } DESCRIPTION "The overall status of the connectivity unit has changed. Recommended severity level (for filtering): alert" ::= 1 -- connUnitAddedTrap , 2, no longer used connUnitDeletedTrap TRAP-TYPE ENTERPRISE fcmgmt VARIABLES { connUnitId } DESCRIPTION "A connUnit has been deleted from this agent. Recommended severity level (for filtering): warning" ::= 3 connUnitEventTrap TRAP-TYPE ENTERPRISE fcmgmt VARIABLES { connUnitEventId, connUnitEventType, connUnitEventObject, connUnitEventDescr } DESCRIPTION "An event has been generated by the connectivity unit. Recommended severity level (for filtering): info" ::= 4 connUnitSensorStatusChange TRAP-TYPE ENTERPRISE fcmgmt VARIABLES { connUnitSensorStatus } DESCRIPTION "The overall status of the connectivity unit has changed. Recommended severity level (for filtering): alert" ::= 5 connUnitPortStatusChange TRAP-TYPE ENTERPRISE fcmgmt VARIABLES { connUnitPortStatus, connUnitPortState } DESCRIPTION "The overall status of the connectivity unit has changed. Recommended severity level (for filtering): alert" ::= 6 END